Your Installation Options
Our Solid Wood flooring can be installed in two different ways, so it depends on your subfloor
and what sort of method you prefer.
Note: This guide is based on straight plank solid wood flooring, so if you’re fitting parquet, please take a look at your parquet-specific guide too.
Nailing
With this method, secret nails go through the tongue to secure the planks to a wooden subfloor. Professional fitters tend to prefer this method as the result is extremely secure. You’ll need to fit a wood layer above any concrete because secret nailing cannot be done directly on top of a concrete subfloor.
Gluing
With this method, adhesive is applied to the top of the subfloor with a trowel and then the individual planks are laid on top. This is our favoured method for tongue and groove parquet flooring.
Good to know
Tongue & Groove
These boards come with a short protruding side (the tongue) and one short indented side
(the groove). These slot together like a jigsaw puzzle to form a tight fit.
Preparing to Fit Your Floor
- Check the packs
Once the flooring arrives you should check one box to make sure you’re happy with the product. Due to the nature of wooden flooring, each plank is unique so there might be some natural variation between the planks and batches. When you get to laying the floor you can make the most of these colour contrasts by mixing and matching planks from different packs to get a lovely natural look.
- Leave to acclimatise
Your solid wood floor should be left for 5-7 days in the room it’s going to be fitted in. This time allows the floor to acclimatise and will reduce the risk of swelling or contracting once the floor is installed. To do this, either lay the packs on the floor or in stacks, just as long as they stay horizontal and that there’s equal weight distributed across them all. Leave the planks in their packaging but open each end to let some air in. Try to make sure the room stays at the same temperature you’d usually have it at so between 18°C – 27°C and don’t allow the floors to be exposed to the elements.
Remember: solid wood floors cannot be fit with underfloor heating.
- Prepare the subfloor
Before you lay your new floor, you’ll need to remove the existing flooring, prepare the subfloor and ensure it is clean, dry and level. We recommend a concrete or wooden subfloor for the best result. Use a moisture meter to check the subfloor is dry enough before you start. If you do have a concrete subfloor, make sure it’s completely dry before installation. A damp-proof membrane should be installed on top of the subfloor to reduce the risk of moisture reaching the solid wood boards. You’ll need to do this to prevent the wood floors from expanding and buckling. Any screws or nails in your subfloor should be fixed below the surface. Remove any old adhesive from previous floors and vacuum the floor to pick up any excess dust or debris.
- Plan the look
Before you start laying your floor, take the planks from the pack and look at the natural grains and deviations in the shade. Pick out your favourites and use these planks as a focal point. Mix and match shades and patterns around these so that you can get a look you’re happy with. If there are a few planks you don’t love as much you could set these aside to use for cuts, or in areas that will be covered by furniture or rugs. Think about the direction you’d like your planks to lie. As a general rule of thumb, lay the boards against the longest wall for the best effect. If it’s a square room you might want to follow the room’s light flow, or follow on from the entrance. If you’ve gone for herringbone or parquet you can choose the direction and style of the pattern and how you want the eye to be drawn when you enter the room. The majority of our fixed length planks come with a starter plank in the pack. This is a shorter piece of wood that you should use to begin laying the pattern so that the flooring has a staggered effect. For random length planks, mix and match the lengths so you get a dappled natural look.
- And one last thing…
It’s best to fit your floor as the last thing you do in a renovation project. Work your way from the top of the room to the bottom so that once you’re ready for the floor to go in, there’s much less chance of damaging it. This counts for new kitchens and islands too so always fit the floor after units have been installed rather than before. This way you’ll make sure your new floor doesn’t buckle under the weight.
Installing Your Floor
- Before laying the boards, measure the width of the final row. You can do this by dividing the total width of the room by the width of an individual board. This will allow you to cut down the first row of boards to ensure the final row is at least 60mm wide.
- You can then lay the first plank in the corner of the longest wall with the groove side of the plank facing the wall. Make sure this row is perfectly straight as this will set the direction for the rest of the floor.
- Place spacers between the first row and the wall to create an expansion gap of 10-12mm.
- We recommend surface nailing the first row of boards with a nail gun to guarantee they are well secured to the wooden subfloor.
- Then you can lay and secret nail the new row with a powered flooring nailer or by hand with Tongue-Tite screws and a screwdriver bit. These nails will go through the tongue and into the subfloor and will be hidden when the tongue fits into the groove.
- Continue to stagger the joints from row to row to create a natural wood appearance.
- Make sure you place spacers consistently to ensure a standard gap from the sidewalls.
- The last row might be tricky but a pull bar and rubber mallet will help to create a tight fit. You probably won’t have much room here so, as with the first row, you should surface nail.
- Before laying the boards, measure the width of the final row. You can do this by dividing the total width of the room by the width of an individual board. This will allow you to cut down the first row of boards to ensure the final row is at least 60mm wide.
- Apply the adhesive 1 metre out from the longest wall before laying your first row.
- You should lay the first plank in the corner of the longest wall with the tongue side of the plank facing the wall. Make sure this row is perfectly straight as this will set the direction for the rest of the floor.
- Place spacers between the first row and the wall to create an expansion gap of 10-12mm.
- As you continue, ensure you place approximately 1 metre of adhesive ahead of the previous row and stagger the joints from row to row to create a natural wood appearance.
- Make sure you place spacers consistently to ensure a standard gap from the sidewalls.
- The last row might be tricky, but a pull bar and rubber mallet can help to create a tight fit.
- Leave the floor for 24 hours before moving furniture back into the room or walking on it.
Finishing the Look
To fit your solid wood floor around any pipes, first mark the position of the pipe in the board you’re
using. Drill a hole in this position and make two angled cuts with a saw. These cuts should form a wedge
from the edge of the board to the hole which can then be removed. Fit the board around the hole and
then reattach this wedge with glue behind the pipe so the plank looks intact.
For fitting around door frames, start by removing the door from the frame. Line up an offcut of flooring along with a threshold bar stacked on top to make sure it will fit underneath the architrave. If needed, use a handsaw and chisel to trim the bottom of the architrave to the correct height. You may also need to trim the bottom of the door before refitting.
You can then use matching beading and thresholds to cover expansion gaps and blend the new floors in with your existing walls, making it look professional and seamless. Make sure not to attach any trims to the flooring itself or it may affect the expansion gaps.
Any spare planks or cuttings can be kept in case any repairs need to be made.
If the expansion gap has been left too large and the skirting or moulding doesn’t cover it, you can use
spare floorboards to cut strips using a hand saw and glue these strips into place.
Forgotten something? It’s not too late to order these…
Your Flooring is Finished!
After putting in the finishing touches (like our range of beautiful radiator pipe covers, skirting boards, stair nosing, and door profiles), you can introduce your furniture, stand back and take it all in. You just fitted your very own Luxury Floor!
We’d love to see your accomplishments! So make sure you take plenty of pictures and post them online
@luxuryflooringfurnishings on Instagram. Tag us #MyLuxuryFloor
We hope you’re happy with your new Solid Wood Flooring but if you have any questions or issues, don’t hesitate to check out our advice centre or get in touch with our customer support team on 0333 577 0025.
The post How to Lay Solid Wood Flooring appeared first on Blog & Advice Centre – Luxury Flooring & Furnishings.
This post appeared first on https://www.luxuryflooringandfurnishings.co.uk